Processing programming and precautions

Case of side drilling: drilling holes at 40mm bar Z-10, 4.2mm drill bit is selected.

 

The symbols in Figure 1 indicate the following actions

Positioning (fast moving FG00).

Cutting feed (linear interpolation G01).

P1: Pause time programmed by address P instruction.

Ma: C axis clamping M code output (a value is set in parameter (NO.5110)).

M(a+1): C axis release M code output.

P2: Pause time set by parameter (NO.5111).

 

Code execution process

The tool is quickly positioned from the starting point to the hole position (that is, the point on the initial plane determined by the hole position data), execute Ma;

Quickly locate to point R;

Cutting feed to the bottom plane of the hole;

Suspend the pause time specified by P;

Quickly return to the R point plane, execute M(a+1) and pause P2 for the specified time;

Quickly return to the initial plane;

 

 

Side drilling machining programming

O2222 (program name)

T0101 (tool number tool compensation)

M63 S2000 (Second spindle forward rotation speed 2000)

G99 M08 (feed coolant per revolution)

G0 X-42Y0 (Quick positioning XY axis)

Z-10 (Quick positioning Z axis)

M14 (spindle switch to position control)

G50 C0 (fix this position as C0)

M45 (spindle holding brake)

G87 X-30 Z-10 R-2

Q1500P1000F0.08 (side drilling cycle)

G80 (cycle cancellation)

G0Z50 (Quick positioning Z axis)

M46 (Cancel the spindle brake)

M15 (spindle switch to speed control)

M65 (the second spindle stops rotating)

M09 (coolant off)

M30 (End of program operation)

 

 

 

Side tapping processing case: tapping at 40mm bar Z-10 (the hole has been drilled with a 4.2mm drill), and the M5x0.8 tap is used.

 

 

 

 

The symbols in Figure 3 indicate the following actions

Positioning (fast moving FG00).

Cutting feed (linear interpolation G01).

P1: Pause time programmed by address P instruction.

Ma: C axis clamping M code output (a value is set in parameter (NO.5110)).

M(a+1): C axis release M code output.

P2: Pause time set by parameter (NO.5111).

 

 

 

 

Code execution process

The tool quickly positions the point from the starting point (that is, the point on the initial plane determined by the hole position data), execute Ma;

Quickly locate to point R;

There are multiple feeding and retreating processes: During the initial cutting from point R, the spindle is rotated forward, only after cutting in the cutting amount q specified by address Q (action 1), the spindle is reversed, and only the parameters are returned After the return amount d (action 2) set in (NO.5213), the spindle is rotated forward to perform (d+q) cutting. (Action 3) After this, before reaching the bottom of the hole (point Z), repeat 2 and 3;

Pause at the bottom of the hole to pause the time specified by P1;

The spindle starts to rotate in the reverse direction, the tapping axis retracts the tool to the R point plane, to the R point plane at the speed specified by F, and the spindle stops rotating at the R point; execute the C axis to release the M code M (a+1), and pause Pause time specified by P2;

Quickly return to the initial plane;

The high-speed deep hole rigid tapping ends.

 

 

 

Side drilling machining programming

O2222 (program name)

T0202 (tool number tool compensation)

G0 X-42Y0 (Quick positioning XY axis)

Z-10 (Quick positioning Z axis)

M14 (spindle switch to position control)

G50 C0 (fix this position as C0)

M25 (second spindle rigid tapping)

G99G88X-30 Z-10

R-2 Q1500F0.8M45 (end tapping cycle)

G80 (cycle cancellation)

G0Z50 (Quick positioning Z axis)

M46 (Cancel the spindle brake)

M15 (spindle switch to speed control)

M65 (the second spindle stops rotating)

M30 (End of program operation)

 

 

 

 

 

03 Matters needing attention in end face drilling and tapping

Switch to the ZpXp plane (G18);

If the tapping is to the end, please modify the parameters 5213 (change to 1000), 5104#6 (change 0 to 1), 5200#7 (change 0 to 1);

Note the forward and reverse rotation of the second spindle.